Tab Content
  • Pranav's Avatar
    12-08-2018, 10:51 AM
    Also if your running a torsen consider buying a new center thurst block and measuring it against what you have. Maybe that's worn too. I replaced...
    12 replies | 225 view(s)
  • Pranav's Avatar
    12-08-2018, 10:46 AM
    You're on the right track But again like I said eliminating end play is key. Can you try make thicker c clips to take your end play down to...
    12 replies | 225 view(s)
  • Pranav's Avatar
    12-04-2018, 11:20 AM
    Also once you get below halfway on rear pads, knock back increases. I am going to make some shims out of old pads for mine.
    12 replies | 225 view(s)
  • Pranav's Avatar
    12-04-2018, 11:19 AM
    Also to confirm are you running stop techs up front with Max float hardware? None of that beveled washer bullshit
    12 replies | 225 view(s)
  • Pranav's Avatar
    12-04-2018, 11:19 AM
    Mine was pretty bad at Hallett. I pulled my c clips and found they we're worn and thin. I put in fresh Dorman c clips and it was a night and...
    12 replies | 225 view(s)
  • Pranav's Avatar
    10-16-2018, 01:17 PM
    Pranav replied to a thread Exhaust cost in General
    Ripley's off 1960/kuykendahl does good work. Tell them the Indian guy in the black Camaro sent you and make sure to tell them you to off track a...
    15 replies | 1293 view(s)
  • Pranav's Avatar
    10-15-2018, 01:12 PM
    If you're missing the rotors, Girodisc makes replacement discs and hardware that fit mustangs and Camaros. You just need the hats for the Camaro.
    7 replies | 571 view(s)
  • Pranav's Avatar
    10-15-2018, 10:28 AM
    The stoptech st-40 kit uses their proprietary type of rotor/hat, not c5. You just have the calipers/brackets? If I were to do it from scratch i...
    7 replies | 571 view(s)
  • Pranav's Avatar
    10-13-2018, 09:33 AM
    Pranav replied to a thread Exhaust cost in General
    I made it myself using the factory y pipe and cats. Rent the exhaust repair kit from AutoZone and get some tubing and bends from summit. It...
    15 replies | 1293 view(s)
  • Pranav's Avatar
    10-11-2018, 12:45 PM
    Pranav replied to a thread NOLA Role Call in Upcoming Events
    So who's in? Daniel and I want to go and I have been working on the car getting it ready. GF has a SW flight in booked for Friday night so we're...
    9 replies | 756 view(s)
  • Pranav's Avatar
    10-08-2018, 04:06 PM
    Pranav started a thread Axle c clips in General
    Has anyone tried making or sourcing thicker c clips for the GM 7.5? Found my rear end had .150 thick c clips. New Dorman clips were .155 ...
    4 replies | 368 view(s)
  • Pranav's Avatar
    10-05-2018, 10:13 PM
    Pranav replied to a thread '18 Spec Miata Cahmpionship in General
    I've never thought I'd ever give the SCCA praise over doing something better than NASA, but wow, in a few short sentences they just called NASA out...
    37 replies | 2723 view(s)
No More Results
About Pranav

Basic Information

About Pranav
Location:
Houston

Statistics


Total Posts
Total Posts
1,305
Posts Per Day
0.53
General Information
Last Activity
12-10-2018 12:45 PM
Join Date
03-05-2012
View Pranav's Blog

Recent Entries

Fire system plumbing

by Pranav on 02-15-2016 at 11:54 PM
Quote Originally Posted by Supercharged111 View Post
Can anyone speculate as to how differently this would have turned out if he were wearing a nomex baclava and had had his visor shut?
What's there to speculate? I believe it was the only unprotected part of his body.

Updated 02-16-2016 at 01:48 AM by Pranav

Categories
Uncategorized

New engine!

by Pranav on 04-19-2015 at 11:43 PM
Quote Originally Posted by Storm Trooper View Post
If you not making power why stress the motor!
Always made me wonder, should we shift at peak HP, or at a calculated point above that that would maximize average HP before+after shift?

Updated 06-19-2015 at 12:50 PM by Pranav

Categories
Uncategorized