• 64GunPilot's Avatar
    08-26-2019, 09:06 AM
    64GunPilot replied to a thread TMS Recap - 2019 in Racing
    So you guys were running flat out through the entire oval section? Top speeds of 130mph ? How did your cars feel? Did they feel like they were...
    31 replies | 1101 view(s)
  • 64GunPilot's Avatar
    08-18-2019, 03:03 PM
    64GunPilot replied to a thread Shop is Going Up in General
    FYI about the lighting. I ordered 6x 8ft LED tube lights 8500lm 72watts each. Two of the tubes were slightly bent, but worked just fine but when I...
    30 replies | 2007 view(s)
  • 64GunPilot's Avatar
    08-18-2019, 02:52 PM
    64GunPilot replied to a thread Shop is Going Up in General
    Wife and I have worked in the 100+ degrees of heat over the past few weekends and finally got 100amp service run to the shop hooked up successfully. ...
    30 replies | 2007 view(s)
  • 64GunPilot's Avatar
    08-18-2019, 02:33 PM
    64GunPilot replied to a thread Engine Block Cracked in Engine
    I have considered it. I want to put a season or two on the TPI. First loves die hard.
    5 replies | 270 view(s)
  • 64GunPilot's Avatar
    08-14-2019, 09:36 AM
    64GunPilot started a thread Engine Block Cracked in Engine
    Well the JB Weld kept the cracked water jacket sealed for 5 track events, the last one being Hallett. It finally failed. I think its time to pull...
    5 replies | 270 view(s)
  • 64GunPilot's Avatar
    07-28-2019, 10:09 PM
    64GunPilot replied to a thread Shop is Going Up in General
    I wish. Insulation is rediculous! $6500ish for 2” spray foam. That’s gonna be last on the list and if I happen to have spare cash laying around. ...
    30 replies | 2007 view(s)
  • 64GunPilot's Avatar
    07-22-2019, 11:44 PM
    64GunPilot replied to a thread Shop is Going Up in General
    Done with floor epoxy. Went with a small American business product called “ColoredEpoxies”. Great company, great customer service, and so far seems...
    30 replies | 2007 view(s)
  • 64GunPilot's Avatar
    07-17-2019, 05:04 PM
    I would be doing COMP School too at TMS Roval....but, since I deploy in October for 9 months, I dont really see the point of doing it now. Probably...
    24 replies | 1767 view(s)
  • 64GunPilot's Avatar
    07-08-2019, 04:16 PM
    64GunPilot replied to a thread Shop is Going Up in General
    Also been researching like crazy electrical service installation. Just submitted my dig request to bury the new service line from the house to the...
    30 replies | 2007 view(s)
  • 64GunPilot's Avatar
    07-08-2019, 04:00 PM
    64GunPilot replied to a thread Shop is Going Up in General
    Construction starts tomorrow. The size is 40wide x 30deep and 12ft walls. Should have a clearance of 13.5ft inside which should allow a lift to lift...
    30 replies | 2007 view(s)
  • 64GunPilot's Avatar
    07-03-2019, 09:29 AM
    64GunPilot replied to a thread Shop is Going Up in General
    It does doesn’t it. The sheet metal is stressed skin that holds it all together just the same as a semi-monocoque aircraft (all sheet metal...
    30 replies | 2007 view(s)
  • 64GunPilot's Avatar
    07-03-2019, 07:33 AM
    64GunPilot replied to a thread Shop is Going Up in General
    Yea, mine is definitely not gonna be built like that. These are examples my salesman provided. $13700 delivered and installed. Not quite the cold...
    30 replies | 2007 view(s)
  • 64GunPilot's Avatar
    07-02-2019, 10:46 PM
    64GunPilot replied to a thread Shop is Going Up in General
    30x40 all metal but not the super heavy duty I Beam frame. Tubular 14gauge framing. Sounds kinda weak, but certified to 120mph wind. Time will...
    30 replies | 2007 view(s)
  • 64GunPilot's Avatar
    07-02-2019, 06:30 PM
    I've seen some folks TIG weld wheels before with success. TIG I have read pulls impurities out and leaves a 100% strength in the material with 95%...
    9 replies | 673 view(s)
  • 64GunPilot's Avatar
    07-02-2019, 06:32 AM
    64GunPilot replied to a thread Shop is Going Up in General
    Not gonna lie....I've been pretty excited about it. Due to lack of funds, its just gonna be a bare bones building with no lights or electricity...
    30 replies | 2007 view(s)
  • 64GunPilot's Avatar
    07-01-2019, 07:52 PM
    64GunPilot started a thread Shop is Going Up in General
    Sold some stuff to afford this. Smaller than I'd like, but it'll do. No, I didnt sell the car.....in case anyone was gonna ax that...
    30 replies | 2007 view(s)
  • 64GunPilot's Avatar
    06-24-2019, 07:41 PM
    Is tire shaving allowed these days? Since all I got is 16" wheels on a 3rd Gen, I'll be rocking these 255/50/16 RA1's possibly shaved if allowed. ...
    17 replies | 1751 view(s)
  • 64GunPilot's Avatar
    06-23-2019, 10:23 AM
    I’ll let you know. I don’t have an ETA for my stuff yet but assuming late July. About 8 years ago I had an LT1 z28 that I was going to build into...
    4 replies | 564 view(s)
  • 64GunPilot's Avatar
    06-22-2019, 09:28 AM
    I have a pair in my household goods shipment. They'll be here probably end of July :( if you can wait that long.
    4 replies | 564 view(s)
No More Results
About 64GunPilot

Basic Information

About 64GunPilot
Location:
Killeen, TX

Signature


__________________________________________________ __________________________________________________ _______________
-Dylan
3rd Gen CMC Wannabee

Statistics


Total Posts
Total Posts
135
Posts Per Day
0.41
General Information
Last Activity
09-12-2019 09:16 AM
Join Date
10-21-2018