Search:

That might not be the best route unless you're a very good welder. Putting in floor mounting plates is one thing, but welding the windshield bar overhead, sprawled across the steering column with the...

My avatar says it's ok, but the harness will be uncomfortable.

88 Fox, 03 Cobra front and rears, XP8 for HPDE over here.

I suppose I was responding more to the 'don't use plate for a firewall' comment than your post. There seemed to be some discussion about the legality of excessively thick boxes earlier; I only...

INTERESTING... and what is the MINIMUM thickness of the so called rear firewall 1", 2" maybe 3"... any chance this rear firewall is located above the rear axles?[/quote]

I don't know what...

Kinda looks like a Lemons race.

I've threatened to do just that, but it's not really my trailer. It is also not a car trailer; it's got rails all around about a foot high.

True story. As a reference point, an 88 Thunderbird bumper will hit the front rail on a 16' trailer. We took the bumper off the Lemons car, but you proably don't want to do that with a real racecar. ...

While we're on the subject, are external seam gloves really all that? I want some to replace my junk Pyrotects for Lemons, but I worry that I'm succumbing to the bling factor of $130 gloves.

Rear-engine? Must be a Porsche guy. :P

I've stumbled on this little chart whilst searching for a LeMons transmission.
http://www.allfordmustangs.com/Detailed/349.shtml
Though I disagree about the 'too low to be useful' comment on first...

Yanked the blowed up motor and poured the requisite trans fluid all over the garage floor. Hoping to have it ready to run at TWS. Strangely though, the last two trips to College Station resulted in...

It'll buff out. :roll:
The car got loose just before the back straight and the Junk Punch mustang was on the outside. The gigundo fiberglass bumper caved in his front fender and ripped off the...

The Mustank turned into a winged Home Repo Camry, I believe.

The one and only. Holy crap, is tech day always a long one. Don't follow the goldbird too long or you'll go blind from smog. See ya out there.

Cupcake Racing returns for glory!

http://lh6.ggpht.com/_moCml6CV4do/S33G_eNzi-I/AAAAAAAABFA/JL1yhBh7DhM/no%20nose.jpg

Bryan, that's my right clavicle, as modified in November '09. The orthopedic surgeon gave me a CD of the x-ray files post-op. Unfortunately, I don't have the broken shot; that one's rather...

Agreed, if you are going to buy one, now is the perfect time!![/quote]

But where are all these cars hiding? I found one in San Francisco on the CMC site. Not that I'm adverse to that kind of...

As a wannabe racer, I get the feeling there is a fair amount of animosity and discontent among several of the guys here. This doesn't paint a real pretty picture, but I'm not ready to build up an...

This is perhaps unsolicited as I'm not exactly tied to AI or CMC, other than really wanting to play in the sandbox. I linked this thread to a friend in film production (I have no connection to this...

Sold! :D bading-ding-ding

I'll be sure to track you down in Houston; that's a little more than I was planning to spend, but with my luck I'll spend more for less car... maybe we should look it over.
I've been out a couple...

ah, nope. I had a red C5Z until about four weeks ago, but was never much for the vette forums. I guess we'll have to meet in Jan.
Carrying on...

I can't think of what or who LG is, but I'm terrible at names and such. I'm doing my best to make all Houston and CS events as they're easy travel for me. Getting to DFW is a drag, but I'm a wuss.

I'm not a rookie yet, but that's the draw for me; "cheap" racing with a proper engine. Meeting and riding with some of the guys at TWS in August and trolling the pits helped cement the deal. Those...