Page 298 of 308 FirstFirst ... 198248288296297298299300 ... LastLast
Results 2,971 to 2,980 of 3071

Thread: So, what did you do today?

  1. #2971
    Senior Member Carroll Shelby
    Join Date
    May 2013
    Location
    Arlington, TX
    Posts
    1,017
    Quote Originally Posted by blk96gt View Post
    Are you using a PM3L?
    yep
    Tyler Gardner
    CMC #13 2015-2017
    SM #013 2018
    www.dfwmustangs.net

  2. #2972
    Senior Member Carroll Shelby Supercharged111's Avatar
    Join Date
    Jun 2014
    Location
    Colorado Springs, CO
    Posts
    1,149
    Can you patch it? I imagine gear oil soaked in will make it a pain.
    RM CMC Director

  3. #2973
    Senior Member Carroll Shelby
    Join Date
    May 2013
    Location
    Arlington, TX
    Posts
    1,017
    Quote Originally Posted by Supercharged111 View Post
    Can you patch it? I imagine gear oil soaked in will make it a pain.
    I've got enough 8.8 housings laying around, just going to replace it.
    Tyler Gardner
    CMC #13 2015-2017
    SM #013 2018
    www.dfwmustangs.net

  4. #2974
    Senior Member Carroll Shelby Fbody383's Avatar
    Join Date
    Aug 2006
    Location
    Pearland, TX
    Posts
    3,269
    Quote Originally Posted by mach1 View Post
    Got my junk back on the lift, found gear oil all over the driver side of the axle around the panhard bar mount, turns out I drove the thing so hard the axle tube ripped open where the LCA bracket is welded to the axle, crazy. I should've been in front of that Silver camaro anyway.
    Fixed.

    I had a main power wire terminal come loose on the drive home - car starts after tech to go on the trailer and dead when I got home. Big hammer. Blunt chisel. Fixed.

    And addressed the non-blinky Aussie shift light while I was in there.
    #39 CMC Camaro
    Orange is Fast!
    CMC-NT01 FTW!

  5. #2975
    Senior Member Grass-Passer
    Join Date
    May 2012
    Location
    Pearland.TX
    Posts
    463
    Quote Originally Posted by Fbody383 View Post
    Fixed.

    I had a main power wire terminal come loose on the drive home - car starts after tech to go on the trailer and dead when I got home. Big hammer. Blunt chisel. Fixed.

    And addressed the non-blinky Aussie shift light while I was in there, and removed A pound of gravel from the storm trooper wall collision.
    Fixed!

  6. #2976
    Senior Member Carroll Shelby Fbody383's Avatar
    Join Date
    Aug 2006
    Location
    Pearland, TX
    Posts
    3,269
    I'll just leave this here: https://www.formula1.com/en/latest/f...ge-livery.html

    Paging AI132... is this thing on? AI132 where are you?
    #39 CMC Camaro
    Orange is Fast!
    CMC-NT01 FTW!

  7. #2977
    Senior Member Carroll Shelby Supercharged111's Avatar
    Join Date
    Jun 2014
    Location
    Colorado Springs, CO
    Posts
    1,149
    Quote Originally Posted by Fbody383 View Post
    I'll just leave this here: https://www.formula1.com/en/latest/f...ge-livery.html

    Paging AI132... is this thing on? AI132 where are you?
    Ya know Ferraris are red just like my car. The most winningest cars ever.
    RM CMC Director

  8. #2978
    Senior Member Carroll Shelby
    Join Date
    Mar 2012
    Location
    Houston
    Posts
    1,449
    Blog Entries
    2
    Went to get the truck inspected today.

    They couldn't get either of their tests stations to talk to the computer, but I tried my own obd2 scanner and their handheld scanner, it worked fine on those.

    Went down the street and their station started to connect if I wiggled their connector.

    Great, so my obd2 port has a loose pin.

    Take it home and start probing the pins till I find the offending one, fix it. Turns out when I did my trans flush a while ago, I shorted two pins to get the truck to go into "transmission fluid level check" mode, and the jumper I used just loosened up that one pin socket enough to piss off the inspection machine, as my own scanner apparently never uses that pin.

    Get in the truck to go back but my abs/brake/VSC lights are all on.

    Great, I pissed the computer off with all of the random probing and grounding of pins.

    I google how to do a zero point calibration, had to disconnect battery and short two obd pins a few times in a sequence.

    All lights off and head back to the station, their scanner worked but four of the emissions tests weren't ready yet so I failed.

    Great, so pulling the battery causes the ECM to start over on all the readiness codes.

    Went on a short trip to get the truck running for a while, stopped for gas.

    All the readiness codes are good to except for the EVAP. Guess why the EVAP wouldn't reach readiness?

    Because I filled up the gas tank. Most cars require something like 1/4 to 3/4 tank to cycle/test the EVAP and produce a readiness code.

    Boat load of fail today.

    Not sure why I even got out of bed.

  9. #2979
    Senior Member Carroll Shelby GlennCMC70's Avatar
    Join Date
    Mar 2006
    Location
    Ft. Worth
    Posts
    6,448
    Blog Entries
    1
    Should pass with a single not ready.

  10. #2980
    Senior Member Carroll Shelby
    Join Date
    Mar 2012
    Location
    Houston
    Posts
    1,449
    Blog Entries
    2
    Oh, I assumed they would fail unless all were ready.

    Was just watching with my own scanner, haven't gone back yet.

Bookmarks

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •