Possible CMC Car at TDE at MSR-H May 2021

[babablackgoat]

I bought this because it was cheap, have been stoked with it so far. I have a custom tire rack on it now. Recommend load leveling springs and class D tires.

You will find that a new cheap-ish trailer is going to need a little tune up from time to time (bearings, wiring, etc).

https://maxxdtrailers.com/c3m-7k-steel-floor-car-hauler

- Josh

Thanks for input and specific suggestion, Josh. Trailer World Katy and Texas Trailer Country seem to carry Maxx-D.

[babablackgoat]

Attempting to look at trailers this week. Work from home allows me some freedom with my time, yet I am kinda supposed to be working too...haha. Starting with an appointment with Nationwide to see what is on the lot and a possible custom trailer.

The following are possible requirements/wishlist accumulated from multiple sources:
1. Metal
2. Wood deck
3. 20 foot
4. Axel brakes
5. Load leveling
6. Long ramps (might not be not required)
7. Removable fenders (probably not required)
8. Place for tie-downs (seems kinda obvious - I believe meaning extra places)
9. Tilt jack for storage (probably not required)
10. LED lights (probably not required)
11. Drop axel (probably not required)
12. Winch (probably not required)

What else should be considered when getting a trailer for a CMC car?

[Fbody383]

4a. AT LEAST 3500lb axles

[BryanL]

How often do you plan to go and how far-bringing the the consideration for renting a trailer or one from uhaul just to make this event. Also with the price of new trailers I would consider looking for a used aluminum trailer especially if your concerned about weight. But also it seems that used trailers really tend to hold their value especially when there isn't much available-at least with enclosed trailers there are hardly any new ones from what I hear.

I just sold my metal 18' dovetail trailer. It was built in 99 and was very stout at 2,500 lbs as I don't think they make them as strong now. I replaced the axles, new goodyears, wiring last year and it sold in 15 minutes on FB for $2,250 I think. An issue with it was the ramps pulled out but stayed in the trailer-you want to be able to put them on the top of the dovetail.

[babablackgoat]

How often do you plan to go and how far-bringing the the consideration for renting a trailer or one from uhaul just to make this event. Also with the price of new trailers I would consider looking for a used aluminum trailer especially if your concerned about weight. But also it seems that used trailers really tend to hold their value especially when there isn't much available-at least with enclosed trailers there are hardly any new ones from what I hear.

Valid points I have been thinking of. Specifically would be nice to get a used aluminum trailer already setup for CMC. Cheaper and lighter. But none are jumping out at me. As you indicated, it seems I might need to rent for this one event. Detail in the next post on my trip to Nationwide Trailers.

[babablackgoat]

Trip to Nationwide was productive using the above requirements/wishlist. Met with "Kyle". Does have exactly what I want on the lot, so spec'ed one out. See "NationwideTrailer_snip_01.JPG".

Cannot have ready for TDE at MSR-H on 15 May 2021, so will probably rent. But this one for me can be ready for Hallett. Nationwide wants a $500 deposit. Looks good to me. Thoughts? Any reason I should not pull the trigger?

And Mosty said I can go to HPDE 3, so I plan to be there.

NationwideTrailer_snip_01.jpg

[Supercharged111]

Trip to Nationwide was productive using the above requirements/wishlist. Met with "Kyle". Does have exactly what I want on the lot, so spec'ed one out. See "NationwideTrailer_snip_01.JPG".

Cannot have ready for TDE at MSR-H on 15 May 2021, so will probably rent. But this one for me can be ready for Hallett. Nationwide wants a $500 deposit. Looks good to me. Thoughts? Any reason I should not pull the trigger?

And Mosty said I can go to HPDE 3, so I plan to be there.

NationwideTrailer_snip_01.jpg

Does that have brakes on one axle or both?